Downloads for Intel® 82579V Gigabit Ethernet PHY
This download record installs version 25.4 of the administrative tools for Intel® Network Adapters.
Linux*
Latest
The 25.4 Intel® Ethernet Adapter Complete Driver Pack has been removed from Download Center for updates and will be replaced with the upcoming 25.4 release.
Latest
This download version 25.4 installs UEFI drivers, Intel® Boot Agent, and Intel® iSCSI Remote Boot images to program the PCI option ROM flash image and update flash configuration options.
Linux*
Latest
Installs Intel® Network Adapter drivers release 25.4 for Windows 8.1*.
Windows 8.1, 32-bit*
Windows 8.1, 64-bit*
Latest
This download contains 25.4 version of the Intel® Ethernet Adapter User Guide.
Latest
Provides Intel® Ethernet Product Software Release Notes.
Latest
This download installs version 3.8.4 of the e1000e Linux* Intel® Network Adapter Driver for Intel® Gigabit Network Connections for PCI Express*.
Linux*
Latest
This download includes version 7.7.8 of the gigabit base driver for Intel® Network Connections.
Latest
Installs Intel® Network Adapter drivers release 25.0 for Windows 7*. — Final Release
Windows 7, 32-bit*
Windows 7, 64-bit*
Latest
This download record installs version 24.3 of the Intel® Ethernet Adapter drivers for MS-DOS*. Final Release
Latest
Disabling TCP-IPv6 Checksum Offload Capability with Intel® 1/10 GbE Controllers
Latest
This installs base drivers, Intel® PROSet/Wireless Software version 22.7.1 for Windows Device Manager*, ANS, and SNMP for Intel® Network Adapters for Windows 8*.
Windows 8*
Windows 8, 32-bit*
Windows 8, 64-bit*
Latest
Provides NVM Update Utility for Intel® 82579V Gigabit Ethernet PHY Network Connection.
Enable and Test Wake On LAN (WOL) in Windows* for Intel® Server Boards S5500 and S5520
Content Type Install & Setup
Article ID 000006559
Last Reviewed 04/15/2020
How do I enable WOL?
Open the Device Manager, click Network adapters, right-click the Network Adapter to be WOL enabled, and click Properties.
Click the Link Speed tab then verify installation of Intel® PROSet/Wireless Software and verify it is the latest version.
Click the Power Management tab and mark the Wake on Magic Packet from power off state check box. Note that other WOL options are available in this section.
How do I test WOL?
Make a note of the MAC address, IP address, and Subnet Mask of the Network Adapter for which WOL was enabled.
Power the system off.
On a remote Windows Server 2008* system that is on the same subnet of the system to Wake Up, run a WOL utility.
The screenshot below shows the use of the Depicus* Wake On LAN GUI. Input the MAC Address, Internet Address (local address in this case), Subnet Mask, Send Options: Local Subnet, Port Number 7 (default port), and then click the Wake Me Up button. On the status bar at the bottom, it reads Magic Packet Sent To 255.255.255.255.
Verify that the remote system powered on correctly.
Включите и проверьте пробуждение по локальной сети (WOL) в ОС Windows * для серверных плат Intel® S5500 и S5520
Тип материала Установка и настройка
Идентификатор статьи 000006559
Последняя редакция 15.04.2020
Как активировать WOL?
Откройте Диспетчер устройств, нажмите « Сетевые платы», щелкните правой кнопкой мыши сетевой адаптер, для которого требуется включить WOL, и нажмите « Свойства».
Перейдите на вкладку « скорость линии », затем проверьте установку по Intel® PROSet/Wireless и убедитесь в том, что это новейшая версия.
Перейдите на вкладку « Управление питанием » и установите флажок « пробуждение по магическому состоянию пакета ». Обратите внимание, что в этом разделе представлены другие варианты WOL.
Как проверить WOL?
Запишите MAC-адрес, IP-адрес и маску подсети сетевого адаптера, для которого была активирована поддержка WOL.
В удаленной системе Windows Server 2008 *, которая находится в той же подсети системы для пробуждения, запустите утилиту WOL.
На следующем снимке экрана показана работа с графическим интерфейсом депикус * Wake on LAN. Введите MAC-адрес, Интернет-адрес (местный адрес в данном корпусе), маску подсети, варианты отправки: локальная подсеть, порт No 7 (порт по умолчанию), а затем нажмите кнопку « пробуждение в режим гибернации ». В строке состояния, расположенной в нижней части экрана, она читает пакет Magic, отправленный на 255.255.255.255.
Проверьте правильность питания удаленной системы.